Products
600W aluminum substrate boost constant voltage constant current adjustable power supply module LED boost driver boost charging power supply -75043
product detail
600W Aluminum Plate DC-DC Boost Step Up Converter Adjustable 10A Constant Current Voltage Power Supply Module LED Driver For Arduino
Product parameters:
Module name: 600W boost constant current module
Module nature: non-isolated boost module (BOOST)
Input voltage: DC 10V-60V
Input current: 10 (MAX)
Static working current: 10mA (when 12V rises to 20V, the higher the output voltage, the static current will increase)
Output voltage: 12-60V continuously adjustable (default output 19V shipment, if you need other voltage, please explain to the shopkeeper.)
Output current: 10A MAX, if more than 6A, please strengthen heat dissipation (related to the input and output pressure difference, the greater the pressure difference, the smaller the output current)
Constant current range: 0.2-10A
Output power: = input voltage*10A, such as: input 12V*10A=120W, input 24V*10A=240W,
Input 36V*10A=1360W, input 60V*10A=600W,
Working temperature: -40~+85 degrees (please strengthen heat dissipation when the ambient temperature is too high)
Working frequency: 150KHz
Conversion efficiency: 92%-96% (efficiency is related to input, output voltage, current, and pressure difference)
Input reverse connection protection: none (note that the positive and negative are not reversed)
Installation method: 4 3mm screw holes
Wiring mode: wiring output
Module size: length 85mm width 52mm height 21mm
Output voltage adjustment:
1. Adjust the CV-ADJ potentiometer, according to your battery or LED, set the output voltage to the voltage value you need. Turn the voltage down clockwise, turn up counterclockwise
Output current adjustment:
2. Adjust the CC-ADJ potentiometer clockwise about 20 turns, set the output current to the minimum, connect the LED, and adjust the CC-ADJ potentiometer to the current you need. For battery charging, after the battery is discharged, connect to the output and adjust the CC-ADJ to the current you need. (When charging, you must use the discharged battery to adjust, because the battery is left The more power, the lower the charging current.)
Note:
Please do not use short-circuit method to adjust the current. The circuit structure of the boost module cannot be adjusted by short-circuit method.
Instructions for use:
1. VIN+ is the positive pole of the input power supply, and VIN- is the negative pole of the input power supply.
2. OUT+ is the positive pole of the output power supply, and OUT- is the negative pole of the output power supply.
3. Constant voltage adjustable range: DC12-60V (clockwise to decrease, counterclockwise to increase),
4. Constant current adjustable range: 0.2A-10A (clockwise to decrease, counterclockwise to increase),
5. When the input current exceeds 6A, heat dissipation needs to be strengthened (the aluminum substrate is attached to the flat metal part),
6. The input voltage cannot be lower than 10V or exceed 60V,
7. The maximum input current cannot exceed 10A, and the power cannot exceed 600W.
8. When using, it must be ensured that the input voltage is lower than the output voltage by more than 2V,
9. Before connecting the load, please adjust the required voltage and current when there is no load (the no-load voltage should be increased by 3-5V when the current is constant),
10. When using a switching power supply or other secondary power supply, please ensure that the power of the power supply should be more than twice the power of this module.
Precautions:
1. The input and output cannot be reversed,
2. The input voltage should not be lower than 10V. If the input voltage is too low, the power supply will be damaged. (Be careful to prevent battery over-discharge when using the battery)
2. When working, the input and output voltage and current can not exceed the maximum value, so as not to damage the power supply.
3. Pay attention to ventilation and heat dissipation when working with full load for a long time to extend the service life of the power supply.
4. Pay attention to dust and moisture.
Application:
1. DIY a regulated power supply, input 12V, and output adjustable from 12-50V.
2. To supply power to your electronic equipment, you can set the output value according to your system voltage.
3. As a vehicle power supply, it can supply power to your laptop, PDA or various digital products.
4. DIY a high-power notebook mobile power supply: equipped with a large-capacity 12V lithium battery pack, so that your books can be bright wherever you go.
5. The solar panel voltage stabilizes.
6. Charging batteries, lithium batteries, etc.
7. Drive high-power LED lights
